| ID | Name | Beschreibung | Bestand |
|---|---|---|---|
| 10000043 | TIP3055 | Bipolartransistor, NPN 15A | 14 |
| 10000230 | TIR1000 - SMD | IrDA Encoder and Decoder | 3 |
| 10001413 | TJA1042T | CAN Transceiver, mit Standby, bis zu 5 Mbit/s | 10 |
| 10000500 | TL071 | low noise j-fet input opamp with offset nulling | 3 |
| 10000480 | TL072 | low noise j-fet input dual opamp | 0 |
| 10000253 | TL317C - SMD | Festspannungsregler, einstellbar, 100mA | 2 |
| 10000272 | TL494 CD - SMD | Pulse-Width-Modulation Control Circuit | 9 |
| 10000219 | TLC555 SMD | General Purpose Timer | 4 |
| 10000264 | TLE4935L | Hall IC, switch | 0 |
| 10001414 | TMC262C-LA | Trinamic Stepper Driver, mit Stall Guard und SPI | 4 |
| 10001407 | TPS 54160 | DC/DC Converter IC, einstallbar, Vin 3.5V - 60V, Vout 0.85V - 58V | 10 |
| 10000220 | TPS73001 - SMD | Festspannungsregler, einstellbar, 1.22-5.5V, 200mA, Low Dropout | 10 |
| 10001301 | tqfp 100 | 3 | |
| 10000761 | Trafo 10.5V 2W | kleiner Trafo 10.5V ausgangspannung, 2W | 4 |
| 10000763 | Trafo 10VA, 12V, 834mA | Trafo von Reichelt: EI 48/16,8 112 | 2 |
| 10000762 | Trafo 12V, 1.5W | kleiner Trafo | 14 |
| 10000760 | Trafo 2x6V, 1W | kleiner 1W Trafo mit 2 getrennten 6V Ausgängen | 14 |
| 10000764 | Trafo 6V, 5VA | 2 | |
| 10000942 | Transmitter Toslink | SPDIF Transmitter TX, Toslink, Simplex | 10 |
| 10000799 | Trimmer, stehend, 100k | Präzisionstrimmer, 25 Gänge, Poti | 11 |
| 10000797 | Trimmer, stehend, 1k | Präzisionstrimmer, 25 Gänge, Poti | 7 |
| 10000800 | Trimmer, stehend, 500R | Präzisionstrimmer, 25 Gänge, Poti | 18 |
| 10000798 | Trimmer, stehend, 5k | Präzisionstrimmer, 25 Gänge, Poti | 4 |
| 10001420 | Trimmpotentiometer Gerade 5k | 34 | |
| 10001323 | Trinket-Powered NeoPixel Goggle Kit Pack | One of the most popular Trinket projects now has its own kit pack! Make your very own programmable NeoPixel goggles with 2 x 16 LED rings and an Adafruit Trinket. It even comes with a rechargeable LiPoly battery and charger. It's a great easy build and when you're done you'll have the coolest accessory. Follow along with our popular Kaleidoscope Eyes tutorial. The pack contains almost everything you need to put a pair of NeoPixel Rings in our costume goggles and power them with an Adafruit Trinket. The LED rings fit perfectly inside 50mm round goggles and we include a 3.7v 150mAh battery and and Micro Lipo charger so you can run the battery and charge it all while contained in the goggles themselves. These are fairly easy to put together and should take around an hour to make. You'll need some basic soldering and hand tools to install the JST connector on the bottom side of the Trinket and connect your NeoPixel rings. We don't include a soldering iron or solder but sell them in the Adafruit store and you can find epoxy or hot glue at most hardware/craft stores. The soldering is easy and is possible to do by beginners, its a 1-2 hour project (30 minutes if you are a kit-making expert!) Check the tutorial page to see what you'll need to complete the project! You'll also need a classic USB Micro B cable to program the Trinket, we don't include it as people tend to have too many USB cables in their desk drawer, but if you need one, you can get it from us here. Please note! They look great, but we don't recommend putting the goggles over your eyes when they're all lit up since the lights can be bright and the goggle lenses can be hard to see out of. However, the goggles work great for costumes/accessories when they're put on top of your forehead! | 1 |